SENSORS
Showing 17–32 of 55 results
-
SENSORS
Kit for infrared Applications
IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 5V (although it seems to be OK down to 3.3V)To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn’t do any decoding of the signal, just passes the ‘raw data’ along.
SKU: A212930.00د.م. Add to cart -
SENSORS
Light Dependent Resistor – LDR
Two cadmium sulphide(cds) photoconductive cells with spectral responses similar to that of the human eye. The cell resistance falls with increasing light
intensity. Applications include smoke detection, automatic lighting control, batch counting and burglar alarm systems.SKU: A11213.00د.م. Add to cart -
SENSORS
MMA7361 Triple 3-Axis Accelerometer
This is a breakout board for Freescale’s MMA7361L three-axis analog MEMS accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ±1.5g and ±6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and 0g-detect which detects linear freefall. Zero-g offset and sensitivity are factory set and require no external devices.
This breadboard friendly board breaks out every pin of the MMA7361L to a 9-pin, 0.1″ pitch header. The sensor works on power between 2.2 and 3.6VDC (3.3V optimal), and typically consumes just 400µA of current. All three axes have their own analog output.
SKU: A111350.00د.م. Add to cart -
SENSORS
MQ-05 Natural Gaz Sensor
The Grove – Gas Sensor(MQ5) module is useful for gas leakage detecting(in home and industry). It can detect H2, LPG, CH4, CO, Alcohol. Based on its fast response time. Measurements can be taken as soon as possible. Also the sensitivity can be adjusted by the potentiometer
SKU: B132340.00د.م. Add to cart -
SENSORS
MQ-135 Air Quality Control Sensor
Sensitive material of MQ135 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensor’s conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration.
MQ135 gas sensor has high sensitivity to Ammonia, Sulfide and Benze steam, also sensitive to smoke and other harmful gases. It is with low cost and suitable for different application.SKU: B131240.00د.م. Add to cart -
SENSORS
MQ-2 Semiconductor Sensor for Combustible Gas
Sensitive material of MQ-2 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensor’s conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration.
MQ-2 gas sensor has high sensitity to LPG, Propane and Hydrogen, also could be used to Methane and other combustible steam, it is with low cost and suitable for different application.SKU: B132540.00د.م. Add to cart -
SENSORS
MQ-3 Alcohol Ethanol Sensor
This alcohol sensor is suitable for detecting alcohol concentration on your breath, just like your common breathalyzer. It has a high sensitivity and fast response time. Sensor provides an analog resistive output based on alcohol concentration. The drive circuit is very simple, all it needs is one resistor. A simple interface could be a 0-3.3V ADC.
SKU: B132940.00د.م. Add to cart -
SENSORS
MQ-4 Methane CNG Gas Sensor
LSensitive material of MQ-4 gas sensor is SnO2, which with lower conductivity in clean air. When the target flammable gas exist, the sensor’s conductivity gets higher along with the gas concentration rising. Users can convert the change of conductivity to correspond output signal of gas concentration through a simple circuit.
MQ-4 gas sensor has high sensitivity to methane, also has anti-interference to alcohol and other gases.SKU: B132440.00د.م. Add to cart
-
-
-
-
SENSORS
Kit for infrared Applications
IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 5V (although it seems to be OK down to 3.3V)To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn’t do any decoding of the signal, just passes the ‘raw data’ along.
-
SENSORS
Light Dependent Resistor – LDR
Two cadmium sulphide(cds) photoconductive cells with spectral responses similar to that of the human eye. The cell resistance falls with increasing light
intensity. Applications include smoke detection, automatic lighting control, batch counting and burglar alarm systems. -
-
SENSORS
MMA7361 Triple 3-Axis Accelerometer
This is a breakout board for Freescale’s MMA7361L three-axis analog MEMS accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ±1.5g and ±6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and 0g-detect which detects linear freefall. Zero-g offset and sensitivity are factory set and require no external devices.
This breadboard friendly board breaks out every pin of the MMA7361L to a 9-pin, 0.1″ pitch header. The sensor works on power between 2.2 and 3.6VDC (3.3V optimal), and typically consumes just 400µA of current. All three axes have their own analog output.
-
-
SENSORS
MQ-05 Natural Gaz Sensor
The Grove – Gas Sensor(MQ5) module is useful for gas leakage detecting(in home and industry). It can detect H2, LPG, CH4, CO, Alcohol. Based on its fast response time. Measurements can be taken as soon as possible. Also the sensitivity can be adjusted by the potentiometer
-
-
SENSORS
MQ-135 Air Quality Control Sensor
Sensitive material of MQ135 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensor’s conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration.
MQ135 gas sensor has high sensitivity to Ammonia, Sulfide and Benze steam, also sensitive to smoke and other harmful gases. It is with low cost and suitable for different application. -
SENSORS
MQ-2 Semiconductor Sensor for Combustible Gas
Sensitive material of MQ-2 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensor’s conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration.
MQ-2 gas sensor has high sensitity to LPG, Propane and Hydrogen, also could be used to Methane and other combustible steam, it is with low cost and suitable for different application. -
SENSORS
MQ-3 Alcohol Ethanol Sensor
This alcohol sensor is suitable for detecting alcohol concentration on your breath, just like your common breathalyzer. It has a high sensitivity and fast response time. Sensor provides an analog resistive output based on alcohol concentration. The drive circuit is very simple, all it needs is one resistor. A simple interface could be a 0-3.3V ADC.
-
SENSORS
MQ-4 Methane CNG Gas Sensor
LSensitive material of MQ-4 gas sensor is SnO2, which with lower conductivity in clean air. When the target flammable gas exist, the sensor’s conductivity gets higher along with the gas concentration rising. Users can convert the change of conductivity to correspond output signal of gas concentration through a simple circuit.
MQ-4 gas sensor has high sensitivity to methane, also has anti-interference to alcohol and other gases.
-
SENSORS
Kit for infrared Applications
IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 5V (although it seems to be OK down to 3.3V)To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn’t do any decoding of the signal, just passes the ‘raw data’ along.
30.00د.م. Add to cart -
SENSORS
Light Dependent Resistor – LDR
Two cadmium sulphide(cds) photoconductive cells with spectral responses similar to that of the human eye. The cell resistance falls with increasing light
intensity. Applications include smoke detection, automatic lighting control, batch counting and burglar alarm systems.3.00د.م. Add to cart -
SENSORS
MMA7361 Triple 3-Axis Accelerometer
This is a breakout board for Freescale’s MMA7361L three-axis analog MEMS accelerometer. The sensor requires a very low amount of power and has a g-select input which switches the accelerometer between ±1.5g and ±6g measurement ranges. Other features include a sleep mode, signal conditioning, a 1-pole low pass filter, temperature compensation, self test, and 0g-detect which detects linear freefall. Zero-g offset and sensitivity are factory set and require no external devices.
This breadboard friendly board breaks out every pin of the MMA7361L to a 9-pin, 0.1″ pitch header. The sensor works on power between 2.2 and 3.6VDC (3.3V optimal), and typically consumes just 400µA of current. All three axes have their own analog output.
50.00د.م. Add to cart -
SENSORS
MQ-05 Natural Gaz Sensor
The Grove – Gas Sensor(MQ5) module is useful for gas leakage detecting(in home and industry). It can detect H2, LPG, CH4, CO, Alcohol. Based on its fast response time. Measurements can be taken as soon as possible. Also the sensitivity can be adjusted by the potentiometer
40.00د.م. Add to cart -
SENSORS
MQ-135 Air Quality Control Sensor
Sensitive material of MQ135 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensor’s conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration.
MQ135 gas sensor has high sensitivity to Ammonia, Sulfide and Benze steam, also sensitive to smoke and other harmful gases. It is with low cost and suitable for different application.40.00د.م. Add to cart -
SENSORS
MQ-2 Semiconductor Sensor for Combustible Gas
Sensitive material of MQ-2 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensor’s conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration.
MQ-2 gas sensor has high sensitity to LPG, Propane and Hydrogen, also could be used to Methane and other combustible steam, it is with low cost and suitable for different application.40.00د.م. Add to cart -
SENSORS
MQ-3 Alcohol Ethanol Sensor
This alcohol sensor is suitable for detecting alcohol concentration on your breath, just like your common breathalyzer. It has a high sensitivity and fast response time. Sensor provides an analog resistive output based on alcohol concentration. The drive circuit is very simple, all it needs is one resistor. A simple interface could be a 0-3.3V ADC.
40.00د.م. Add to cart -
SENSORS
MQ-4 Methane CNG Gas Sensor
LSensitive material of MQ-4 gas sensor is SnO2, which with lower conductivity in clean air. When the target flammable gas exist, the sensor’s conductivity gets higher along with the gas concentration rising. Users can convert the change of conductivity to correspond output signal of gas concentration through a simple circuit.
MQ-4 gas sensor has high sensitivity to methane, also has anti-interference to alcohol and other gases.40.00د.م. Add to cart